dimensions in inches and (millimeters) TO-220AB features glass passivated chip junction. high efficiency, low vf high current capability high reliability high surge current capability low power loss mechanical data cases: TO-220AB molded plastic epoxy: ul 94v-0 rate flame retardant terminals: pure tin plated, lead free. polarity: as marked high temperature soldering guaranteed: 260 o c/10 seconds .16?,(4.06mm) from case. mounting position: any weight: 2.24 grams maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol fr 1001g fr 1002g fr 1003g fr 1004g fr 1005g fr 1006g fr 1007g units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current see fig. 1 i (av) 10 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 125 a maximum instantaneous forward voltage @ 5.0a v f 1.3 v maximum dc reverse current @ t c =25 o c at rated dc blocking voltage @ t c =125 o c i r 5.0 100 ua ua maximum reverse recovery time ( note 1) trr 150 250 500 ns typical junction capacitance (note 3) cj 40 pf typical thermal resistance r jc (note 2) r jc 3.0 o c/w operating and storage temperature range t j ,t stg -65 to +150 o c notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. thermal resistance from junction to case per leg mounted on heatsink size 2? x 3? x 0.25? al-plate. 3. measured at 1mhz and applied reverse voltage of 4.0 volts d.c. fr1001g-fr1007g isolated 10amp. glass passivated fast recovery rectifiers http://www.luguang.cn mail:lge@luguang.cn
tj=25 c 0 tj=125 c 0 fig.1- maximum forward current derating curve average forward current. (a) 0 50 100 150 12 10 8 6 4 2 case temperature. ( c) o fig.3- maximum non-repetitive forward surge current peak forward surge current. (a) 1 2 5 10 20 100 50 150 125 100 75 50 25 0 number of cycles at 60hz tj=125 c 0 8.3ms single half sine wave jedec method fig.4- typical junction capacitance capacitance.(pf) 0.1 0.5 1 5 10 50 100 500 1000 150 100 50 0 reverse voltage. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 fig.6- reverse recovery time characteristic and test circuit diagram 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm ratings and characteristic curves (fr1001g thru fr1007g) fig.5- typical instantaneous forward characteristics per leg rofsuoenatnatsni tnerrucdraw )a(. 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 0.1 0.2 0.4 1 2 4 10 20 40 80 instantaneous forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o fig.2- typical reverse characteristics per leg instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 1000 100 10 1 0.1 percent of rated peak reverse voltage. (%) fr1001g-fr1007g isolated 10amp. glass passivated fast recovery rectifiers http://www.luguang.cn mail:lge@luguang.cn
|
